Showing posts with label electronics components. Show all posts
Showing posts with label electronics components. Show all posts

Transport Layer

The transport layer is responsible for source to destination delivery of the entire message. The transport layer ensures that the whole message arrive intact and in order and check all the packets relation to each other. Also check the error control and flow control at source to destination level.
For additional security, network layer may create the connection between two end ports. It involves the etablishment, data transfer and connection release.
Transport layer have following responsibilities;

  • Service point addressing; As compters run many programs at the same time. So here source to destination delivery is not from one computer to other but it is froma specific program on one computer to a specific program on the other. Therefore transport layer header must include a service point address or port address.The transport layer gets the entire message to the correct program running on computer.
  • A mesasge is divided into transmittable segmentrs, each segment contains a sequence number. These number used in reassembling.
  • The transport layer can be connectionless or connection oriented. In connectionless it simply deliver packet to network layer at destination but in connection oriented it makes connection with the transport layer and then deliver packets.
  • Like data link layer it is responsible for flow control. Here flow control is end to end not on a single link.
  • Like data link layer it is responsible for error control. It makes sure that the entire message is delivered correctly at the destination without any error.
                                                          

                                   
Read More!

Hybrid Topology

Hybrid topology is the combination of using diffrent topologies with one as a backbone.
For example, a tree topology used as a back bone and secondry ring topology is used. So here the tree topology is backbone of ring topology and controlling the traffic and communication between the devices of all ring topolgy and may also attached devices in the tree topology itself.
Read More!

Mesh Topology

In a mesh topology every device has a dedicated point to point link to every other device. The term dedicated means that the link carries traffic between the only two connected devices. Therefore in a mesh topology used network has n(n-1)/2 links to n devices. For these links each device must have n-1 input/ouput ports.


Advantages:

1. Traffice errors resolved as each link carries its own data.
2. The disconnection of one link do not disturb the other links and network.
3. The privacy and security remains as only receipent can see the data using a dedicated link.
4. Using the dedicated link to locate the fault and to isolate is much easy.

Disadvantages:


1. The much number of cables and ports in devices are required.
2. Also the installation and reconfiguration is difficult.
3. More space is required for the cabling.

Therefore the mesh topology is apllied to a limited networks or it is used as a backbone in hybrid networks.
Read More!

Topology

The term topology refer to the representation of a network laid out either physically or logically.
When two or more devices are connected to a link then two or more links form a topology. It show the links of the entire network with the devcies attached for communication.

There are five basic topologies used for the communicating devices.

1. Mesh Topology
2. Star Topology
3. Tree Topology
4. Bus Topology
5. Ring Topology

There are two possible relationships for connecting the devices.


Peer-to-Peer
In peer to peer devices share the same link equally.

Primary-Secondary
In primary secondry devices one device controls the traffic and the others communicate through it.

Mesh and Ring topologies mostly use the peer to peer transmission. While Tree and Star topologies convenient for primary secondry connections. But Bus topology is equally convenient to both peer to peer and primary secondary.
Read More!

Norton's Theorem

Named after E,L. Norton, a scientist with bell telephone Laboratories Norton’s theorem is used for simplifying a network in terms of current instead of voltages. In many cases, analyzing the division of currents may be easier than voltage analysis. For current analysis, therefore, Norton’s theorem can be used to reduce a network to a simple parallel circuit, with a current source. The idea of a current source is that it supplies a total line current to be divided among parallel branches, corresponding to voltage source applying a total voltage to be divided among series components. This comparison is illustrated in Fig.10-7.

EXAMPLE OF A CURRENT SOURCE

A source of electric energy supplying voltage is often shown with a series resistance which represents the internal resistance of the source, as in Fig.10-7a. This method corresponds to showing an actual voltage source, such as a battery for dc circuits. However, the source may be represented also as a current with a parallel resistance, as in Fig.10-7b. Just as a voltage source is rated at, say, 10V , a current source may be rated at 2 A . For the purpose of analyzing parallel branches, the concept of a current source may be more convenient than a voltage source.
If the current I in Fig. 10-7is a 2-A source, it supplies 2A no matter what is connected across the output terminals A and B. Without anything connected across A and B, all 2 A flows through the shunt R. When a load resistance R/L is connected across A and B, then the 2-A I divides according to the current division rules for parallel branches.
Remember the parallel current divide inversely to branch resistance but directly with conductance. For this reason it may be preferable to consider the current source shunted by the conductance G, as shown in Fig. 10-7c. we can always convert between resistance and conductance, because 1/R in ohms is equal to G in siemens.
The symbol for a current source is a circle with an arrow inside, as shown inFig.10-7b and c, to shown the direction of current . This direction must be the same as the current produced by the polarity of the corresponding voltage source.
Remember that a source produce electron flow out from the negative terminal.
An important difference between voltage and current sources is that a current source is killed by making it open, compared with short-circuiting a voltage source. Opening a current source kills its ability to supply current without affecting any parallel branches. A voltage source is short-circuited to kill its ability to supply voltage without affecting any series components.
Read More!

Millman's Theorem

Millman’s theorem provides a shortcut for finding the common voltage across any number of parallel branches with different voltage sources. A typical example is shown in fig. 10-16 For all the branches, the ends at point Y are connected to chassis ground. Furthermore, the opposite ends of all the branches are also connected to the point X. The voltage V/x y, therefore, is the common voltage across all the branches.











Finding the value of V/x y gives the net effect of the all source in determining the voltage at X with respect to chassis ground. To calculate this voltage
 v/x y=V1/R1 + V2/R2 + V3/R3 ……etc
1/R1 + 1/R2 +1/R3
This formula is derived from converting the voltage source to current sources and combining the results. The numerator with V/R terms is the sum of the parallel current sources. The denominator with 1/R terms is the sum of the parallel conductances. The net V/x y then is the form of I/G or 1*R, which is in units of voltage.
CALCULATING V/XY
For the values in Fig.10-16,
Vxy =32/4 + 0/2 – 8/4
1/4 + 1/2 + 1/4
=8 + 0 -2
1
Vxy=6 V
Note the branches 3, V3 is considered negative because it world make point X negative. However, all the resistances are positive. The positive answer for Vxy means that point X is positive with respect to Y.
In branch 2, V2 is zero because this branch has no voltage source however, R2 is still used in the denominator.
This method can be used for any number of branches, but they must all be in parallel, without any series resistance between the branches. In a branch with several resistance, they can be combined as one Rt. When a branch has more than one voltage source, they can be combined algebraically for one Vt. Read More!

Alternating Current Application

Figure 16-1 shows the out put from an voltage generator, with the reversals between positive and negative polarities and the variations in amplitude. In Fig. 16-1a, the wave from shown simulates an ac voltage as it would appear on the screen of an oscilloscope, which is an important test instrument for ac voltages. The oscilloscope shows a picture of any as voltage connected to its input terminals, while indicting the amplitude. The details of how to use the oscilloscope for ac voltage measurements are explained in App. D. “Using the oscilloscope”.
In Fig.16-1b the Read More!

Faraday's Law of Induced Voltage

The voltage induced by magnetic flux cutting the turns, of a coil depends upon the number of turns and how fast the flux moves across the conductor. Either the flux or the conductor can move. Specifically, the amount of induced voltage is determined by the following three factors.
1) Amount of flux. The more magnetic lines of force that cut across the conductor, the higher the amount of induced voltage.
2) Number of turns. The more turns in a coil, the higher the induced voltage. The V/ind is the sum of all individual voltages generated in each turn in series.
3) Time rate of cutting. The faster the flux cuts a conductor, the higher the induced voltage. Then more lines of force cut the conductor within a specific period of time.
These factors are fop fundamental importance in many applications. Any conductor with current will have voltage induced in it by a change in current and its associated magnetic flux.
The amount of induced voltage can be calculated by faraday’s law:

 V/ind =N d (Weber’s)
dt (seconds)
Where N is the number of turns and d/dt specifies hoe fast the flux cuts across the conductor. With d/dt in Weber’s per second, the induced voltage is in volts.
As an example, suppose that magnetic flux cuts across 300 turns at the rate of 2 Wb/s.
To calculate the induced voltage,
 V/ind = N d
Dt
=300 (2)
V/ind = 600 V
It is assumed that all the flux links all the turns, which is true with an iron core Read More!

Oscillator

An oscillator is a circuit that produces a repetitive waveform on its output with only the dc supply voltage as an input.A repetitive input signal is not required.The output voltage can be either sinusoidal or nonsinusoidal depending on the type of oscillator.

The basic concept of an oscillator is illustrated in figure(a).Essentially an oscillator converts electrical energy in the form of dc to electrical energy in the form of ac.A basics sinusoidal oscillator consists of an amplifier for gain( either discrete transistor or op-amp ) and a positive feedback circuit that produces phase shift and provides attenuation,as shown in figure(b).


The basic oscillator concept showing three common types of output waveforms sine wave,square wave and sawtooth.

Oscillator Principles:

Positive Feedback:

Positive feedback is characterized by the condition wherein a portion of the output voltage of an amplifier is fed back to the input with no net phase shift,resulting in a reinforcement of the output signal.This basic idea is illustrated in figure.As you can see the in phase feedback voltage Vf is amplified to produce the output voltage which in turn produces the feedback voltage.That is,a loop is created in which the signal sustains itself and a continous sinusoidal output is produced.This phenomenon is called oscillation.



Conditions for Oscillation:

Two conditions are required for a sustained state of oscillation.
1.The phase shift around the feedback loop must be zero degree.
2.The voltage gain Acl,around the closed feedback loop (loop gain) must equal 1 (unity).

The voltage gain around the closed feedback loop(Acl) ia the product of the amplifier gain (Av) and the attenuation (B) of the feedback circuit.

Acl=Av.b

For example,if the amplifier has a gain of 100,the feedback circuit must have a attenuation of 0.01 to make the loop gain equal to 1( that is Av.B=100*0.01=1).These conditions of oscillation are illustrated in figure.



Start-Up Conditions:

So far,you have seen what it takes for an oscillator to produce a continous sine wave output.Now let's examine the requirements for the oscillation to start when the dc supply voltage is turned on.As you know,the unity-gain condition must be met for oscillation to be sustained.For oscillation to begin,the voltage gain around the positive feesback loop must be greater than 1 ,so that the amplitude of the output can be build up to a desired level.The gain must then decrease to 1 so that the output stays at the desired level
Read More!

Voltage Multipliers


Voltage Doubler:

Half wave Voltage Doubler:
A voltage doubler is a voltage multiplier with a multiplication factor of two.A half wave voltage doubler is shown in figure below:



During the positive half-cycle of te secondary voltage,diode D1 is forward-biased and D2 is reverse-biased.Capacitor C1 is charged to the peak of the secondry voltage (Vp) less the diode drop with the polarity shown in part (a).During the negative half-cycle,diode D2 is forward-biased and D1 is reverse-biased,as shown in part (b).Since C1 can't discharge,the peak voltage on C1 adds to the secondary voltage to charge C2 to approximately 2Vp.Applying Kirchhoff's law around the loop as shown in part (b),the voltage across C2 is

Vc1-Vc2+Vp=0
Vc2=Vp+Vc1

Neglecting the diode drop of D2,Vc1=Vp,therefore,

Vc2=Vp+Vp=2Vp

Under a no load condition ,C2 remains charged to approximately 2Vp.If a load resistance is connected across the output,C2 discharges slightly through the loadon the next positive half-cycle and is again recharged to 2Vp on the following negative half-cycle.The ersulting output is a half-wave,capacitor filtered voltage.The peak inverse voltage across each diode is 2Vp.




Full Wave Voltage Doubler:
A full-wave doubler is shown in figure.When the secondary voltage is positive,D1 is forward-biased and C1 charges to approximately Vp,as shown in part (a).During the negative half-cycle,D2 is forward-biased and C2 charges to approximately Vp,as shown in part (b).The output voltage,2Vp is taken across the two capacitors in series.





Voltage Tripler:
The ddition of another diode-capacitor section to the half-wave voltage doubler creats a voltage tripler,as shown in figure.The operationis as follows:On the positive half-cycle of the secondary voltage,C1 charges to Vp through D1.During the negative half-cycle,C2 charges to 2Vp through D2,as described for the doubler.During the next positive half-cycle,C3 charges to 2Vp through D3.The tripler output is taken across C1 and C3,as shown in figure.



Voltage Quadrupler:
The addition of still another diode-capacitor section,as shown in figure,produces an output four times the peak secondary voltage,C4 charges to 2Vp through D4 on a negative half-cycle.The 4Vp output is taken across C2 and C4,as shown.In both the tripler and qudrupler circuits,the PIV of each diode is 2Vp.



Read More!

Diode Limiter

The diode limiter also called Clipper as it is used to limit the input voltage.when the positive cycle of the input wave comes, the diode becomes forward biased (fig. 2). As the cathode now at zero volts 0 v,the anode cannot exceed 0.07 volts assuming diode is a silicon diode.

So it limited to 0.7 volts as positive cycles comes from input voltage.When negative cycle comes the diode become reverse biased and at the output load we only get the negative cycle with clipped positive cycle.

And if we put the diode in reverse we will get the positive cycle with the clipped negative cycle
as shown below in the figure.





Figure 1: Shows the input
Figure 2: positive cycle clipped.
Figure 3: Negative cycle clipped.
Figure 4: Both the positive and negatice cycles are clipped. Read More!

 
Design by Wordpress Theme | Bloggerized by Free Blogger Templates | coupon codes